Cart
/

User Manual DDJR001/DDJR002 EN

 

Product Structure

 

No.

Name

Function

1

Gear switch

Used to control product switch and fast and slow motor speed

2

Motor components

Main parts, with components (e.g. electric switch) inside

3

Transparent cover

Covered on the meat cup for safety protection

4

Container (thickened glass bowl, stainless steel bowl)

Used to store food

5

Blade components

Used for chopping food

6

Non-slip pad

Used for machine anti-skidding

Technical parameters

Product name

Food processor (meat crusher)

Product model

CH-209 CH-209C M-209 M-209C M-209A M-209B M-2091 M-2092 M-2093 M-2095

Rated voltage

220V-

Rated frequency

50Hz

Rated power

300W

Cup material

304 stainless steel / thickened glass

  1. S-shaped three-dimensional four-blade design to achieve better effect of mincing meat and vegetables;
  2. High and low grade design, two options available, which can control the degree of food shredding, featuring better taste, and being safe to use;
  3. Thickened glass bowl / stainless steel bowl, which is healthy and easy to clean.

 

Electrical schematic diagram

(Circuit diagram is for reference only)

Use method

  1. Use steps
  2. Remove the main unit and cup cover, place the stainless steel bowl / glass bowl in a flat place, and then place the non-slip pad under the bowl.
  3. Take out the plastic blade sleeve used to protect the blade.
  4. Make sure the meat cutter is put on the rotating shaft in the middle of the bowl.
  5. Put in food (refer to food weight/ work schedule);
  6. The ingredients added shall not exceed the upper limit of the maximum mark of the bowl.
  7. Cover the bowl cover, and then put the main unit on the bowl cover, check whether it is placed flat and neat, and make sure that the main unit is installed with the meat cutter and bowl cover.
  8. Insert the power cord and connect the power.
  9. Hold the main unit by hand, press the switch, and the machine starts to work. Release the switch, it stops working (refer to food weight/ work schedule);
  10. After the machine stops working, please do not take off the main unit immediately. After the blade components stop rotating, unplug the power plug and then take off the main unit.
  11. Open the bowl cover. Take out the meat cutter first, and then take out the food.



The meat cutter is very sharp. When taking out, take care not to cut hands or other parts of human body.

 

Warm Prompts:

Please do not put water higher than 50 ℃ water or food ingredients into the bowl for processing, to avoid deformation of main unit by heat.

  1. Recommended food weight/ work schedule

Recommended food

Recommended weight

Maximum chopping and mixing time

Remarks 

Pork

Approx. 300g (cut into small pieces of approx. 2cm first)

30s

Remove bone, skin and tendon and use II gear. Adjust the working time according to your taste. Generally, it can be completed in 8-20 seconds

Beef

Approx. 300g (cut into small pieces of approx. 2cm first)

30s

Remove bone, skin and tendon and use II gear. Adjust the working time according to your taste. Generally, it can be completed in 8-20 seconds

Garlic

Approx. 300g

30s

Use I gear. Adjust the working time according to your taste. Generally, it can be completed in 15-20 seconds

Pepper

Approx. 300g

30s

Use I gear. Adjust the working time according to your taste. Generally, it can be completed in 15-20 seconds

Carrot

Approx. 300g (cut into small pieces of approx. 2cm first)

30s

Use I gear. Adjust the working time according to your taste. Generally, it can be completed in 15-20 seconds

Vegetables

Approx. 300g

30s

Use I gear. Adjust the working time according to your taste. Generally, it can be completed in 15-20 seconds

Remarks: 1. Please refer to operation of similar food in the table above for the food not indicated in the table;

  1. Use inching function for single gear vegetable cutting.

Points for Attention

  1. Do not use voltages other than rated voltage marked on the nameplate, otherwise there is a risk of electric shock or fire.
  2. Use separate socket of 6A or above. If the socket is shared in use with other electrical appliances, the circuit part of the socket may cause abnormal heating and fire.
  3. Hold the power cord plug by hand and insert it into the power socket steadily.
  4. Do not use hard iron objects to scratch the machine.
  5. After use of the machine, the power cord plug must be pulled out, otherwise there may be the danger of electric shock, electric leakage and fire.
  6. This product cannot be used to process hard things, e.g. meat with bones, coffee beans, pepper, Chinese prickly ash, ice or frozen food.
  7. It is strictly prohibited to put the glass bowl / stainless steel bowl into the microwave oven for heating.
  8. Prior to adding food, please check whether the chopper blade has deviated from the correct position. If the blade fails to operate quickly in a few seconds, please unplug the plug first, level or take out excessive food, and then continue to use.
  9. The blade is very sharp. Please don’t touch the blade directly with your hands. When taking out and installing, hold the holder of blade, and don’t touch the blade.
  10. The continuous working time of this product shall not exceed 30 seconds. In case that it works continuously for 30 seconds, it must rest for 2 minutes for use again. It takes an interval of 2 minutes after working for 30 seconds and 3 times as a cycle, if it works continuously until the temperature controller works, it will resume working after the motor cools down.
  11. In case of power cord damage, to avoid danger, it must be replaced by professionals from the manufacturer, its maintenance department or similar departments.
  12. The blade of this machine is sharp. Take care when taking out the blade, discharging the mixing basin and during cleaning.
  13. If the product stops working during operation, it may be caused by temperature control protection of motor. Please turn off the power and wait for 20-30 minutes for cooling before use again.
  14. The product shall be stored in a place out of the reach of children. Do not allow people (including children) with incomplete limbs, sensory or mental disorders or lack of relevant experience and knowledge to use or play with the product.

Maintenance and maintenance

  1. After use, please unplug the power plug from the power socket in a timely manner.
  2. The blade components can be disassembled and cleaned. For safety, it is recommended to wear gloves.
  3. After cleaning, it can be assembled after drying. The blade shall be well covered with sleeve to avoid cutting hand.
  4. All parts can be cleaned with detergent and sponge. Do not use hard steel wire to avoid causing damages to the surface.
  5. Do not immerse the whole machine in water. The external surface of the product can only be wiped with a wet towel. Do not wash it with water to avoid electric leakage and fault.
  6. In case of no use of product for a long time, please clean and put it in the packaging box, and put it in a ventilated and dry place, to avoid from getting damp and affecting use.

Analysis of Common Problems

Fault Phenomenon

Cause Analysis

Troubleshooting

No working after power on

The bowl cover is not well covered

Cover the bowl well

The machine stops during use

1.  The voltage is too low

2. Motor overload automatic stop protection

  1.   Check the voltage;

2. It is recommended to leave the machine for 30 minutes and then start the machine.

The motor produces a bad smell after first uses

It is normal when new motor is used for the first time

In case of still a bad smell after repeated use, please send it to the maintenance point for inspection.

Abnormal vibration or large noise

1.  Meat cutter blade holder is not installed in place

2.  The product is not placed steadily

3.  The voltage is too high

4.  Excessive ingredients

1. Take out the ingredients and install the blade holder in place

2. Place the product stably

3.  Check whether the voltage is too high

4. Turn off the power and take out the excessive ingredients