Cart
/

User Manual DZGH002/DZGH003 EN

 

Electric Caldron

User Manual



Safety Precautions

  1. Please read carefully and abide by the following safety precautions prior to use.
  2. The product shall be used together with the power cord supplied, and other power cords shall not be used.
  3. Dry the water marks on the bottom cover of the caldron body prior to use.
  4. Stay at the side while the product is working. Do not leave the product unattended to avoid accidents.
  5. Do not place the product within the reach of children or mentally handicapped persons to prevent scalding.
  6. When using, place the product on a flat surface, not close to other heat sources, nor on other electrical appliances.
  7. When the product is operating, do not touch the steam released from the glass cover to prevent scalding.
  8. Do not add water beyond the maximum water level to prevent boiling water from splashing out and scalding people; nor lower than the minimum water level to avoid product damage caused by dry burning of the heating plate. Cover the glass cover when boiling water.
  9. For using for the first time, add water to the maximum water level, and then boil the water and pour it out, to clean the caldron body.
  10. Do not hang the power cord around the table or contact hot objects.
  11. Do not immerse the caldron body in water or other liquids for cleaning to avoid short circuit.
  12. Please use the power socket with the voltage consistent with the voltage indicated on the product nameplate.
  13. In case of power cord damage, it must be replaced with a special flexible cord or a special component purchased from its manufacturer or maintenance department.
  14. The power supply cannot be connected under the following conditions: no water in the caldron, when adding water, cleaning or moving the product.
  15. In case of any fault, please send the product to the special maintenance center for maintenance prior to use. The user shall not repair it by himself. To avoid electrical hazards, please do not disassemble the bottom cover or the power cord by yourself.
  16. This product is only available for use indoors or in similar places.



Product Structure Diagram

Note: The product drawing is only for reference, and it shall be subject to the actual products or accessories.

Use Method

Boil water

  1. Remove the cover, add clean water, neither below the minimum water level nor above the maximum water level, and then cover the cover.
  2. Plug the power plug into the power supply, turn the switch knob to “II”, the indicator light goes on, and the product starts heating.
  3. After approx. 10 minutes, the water begins to boil. Turn the switch knob to “Off”, the indicator light goes off, and the product stops heating.

Cook noodles

  1. Remove the cover, add clean water, neither below the minimum water level nor above the maximum water level, and then cover the cover.
  2. Plug the power plug into the power supply, turn the switch knob to “II”, the indicator light goes on, and the product starts heating.
  3. After approx. 10 minutes, the water begins to boil. Put the noodles into the caldron and the water temperature reduces. After the water boils again, add seasoning and mix evenly. Turn the switch knob to “Off”, the indicator light goes off, and the product stops heating.

Hot pot

  1. Remove the cover, add clean water, neither below the minimum water level nor above the maximum water level, and then cover the cover.
  2. Plug the power plug into the power supply, turn the switch knob to “II”, the indicator light goes on, and the product starts heating.
  3. After about 10 minutes, the water begins to boil. Put the hot pot materials into the caldron and cook them. Then you can enjoy the food after cooking. To reduce the fire power, turn the switch knob to “I”. If you don't want to heat, turn the switch knob to “off” and turn off the power supply.

Cooking function (hot dish)

  1. Remove the glass cover, add proper amount of water, put the steaming rack in the caldron, then put the egg white and egg yolk stirred evenly in the box, put the box on the steaming rack, and cover the glass cover.
  2. Plug the power plug into the power supply, turn the switch knob to “II”, the indicator light goes on, and the product starts heating.
  3. After approx. 7-8 minutes, the water begins to boil. After the eggs are well steamed, turn the switch knob to a proper shift for constant temperature heating for a period of time. After reaching the desired effect, turn the switch knob to “On/Off” and turn off the power supply.