Shopping Cart
Home
/
CORDLESS WET DRY VACUUM CLEANER XDJH004 User Manual English Version

CORDLESS WET DRY VACUUM CLEANER XDJH004 User Manual English Version

SPECIFICATIONS

Product name

Voltage

Rated power

Clean water cup capacity

Sewage cup capacity

Cordless wet dry vacuum cleaner

21.6V

200W

850ml

750ml

 

ILLUSTRATION

1.Handle

2.Aluminum tube

3.Clean water cup

4.Rolling brush storage base

5.Rolling brush release button

6.Power button

7.Gear switch

8.Self-clean button

9.Display screen

10.Sewage cup release button

11.Sewage cup

12.HEPA storage base

13.Rolling base cover

14.Hot air dry charging base

  1. Standard mode
  2. Intelligent mode
  3. Low water level indicator
  4. Rolling brush cleaning
  5. Full sewage cupindicator
  6. Power mode
  7. Abnormal rolling brush indicator
  8. Electrolysis water
  9. Drying sterilization

  1. HEPA filter storage base
  2. HEPA filter
  3. Rolling brush
  4. Charging base
  5. Handle
  6. Body
  7. Cleaning brush
  8. Cleaning fluid
  9. Fragrance kit
  10. Rolling brush storage kit

 

ASSEMBLY

  1. Handle
  • Assembly: Stick the handle to the slot of the body vertically till you hear a click. (on left)
  • Disassembly: Remove the plug on the back of the body. Use a slender tool into the hole and press. Pull out the handle. (on right)

  1. Clean water cup
  • Assembly: Put the clean water cup into the slot of the body till you hear a click. (on left)
  • Disassembly: Press the clean water cup release button and pull out. (on right)

  1. Sewage cup
  • Assembly: Put the sewage cup into the slot of the body till you hear a click. (on left)
  • Disassembly: Press the sewage cup release button and pull out. (on right)

  1. Rolling brush cover
  • Assembly: Apply your finger to the shown position and release the thumb and forefinger at the same time.Press the put button down till you hear 2 clicks.
  • Disassembly: Apply your finger to the same position as shown. Use thumb and forefinger to press both ends to release the button upwards. Lift up and remove the roller cover

 

  1. Rolling brush
  • Disassembly: Press the rolling brush release button on the left side. Pull up the roller handle at the left end and pull outward to remove the roller brush.
  • Assembly: Snap the handle into the left side slot and install the roller. Fix the brush upper cover completely.

  1. Fragrance kit
  • Remove clean water cup first. Pinch the kit slot and rotate it counterclockwise 45°to take it
  • Put the fragrance tablets in the kit slot.
  • Then rotate the kit slot clockwise 45°into the body.

 

OPERATION

  • Mode switching
  1. The ON/OFF button is on the handle. Press the button to turn on the appliance.The default mode is Auto mode. Press the button again to turn off the appliance.
  2. When the appliance is working, press the power switch to switchmodes among Standard Mode, Power Mode and Absorption Mode.

ON/OFF button

Power switch

Self-clean button

  1. Filling up clean water cup
  • Press the clean water cup release button, and remove the cup.
  • Open the upper cover and fill up with clean water(under 60℃) till it meets the water line. For deep clean, please add 16ml (about two bottle caps) floor cleaning fluid.

  • Close the upper cover of the cup tight and ensure no leakage.
  • Reassemble the clean water cup to the bodytill you hear a click.

 

  1. Charging
  • Place the appliance on the charging base. Connect the charger to the power socket.
  • Put away the charger when not charging. Place the appliance upright near the wall corner to avoid trip and injury.
  1. Self-cleaning
  • Put the appliance back to charging base after usStart the self-cleaning procedure when necessary.
  • Press the self-clean button to start procedure.
  • After self-cleaning, the appliance enters charging status and starts the rolling brush auto air dry modeby default.

 

MAINTENANCE

  1. Body
  • Turn off the power before cleaning the appliance.
  • Clean the body by soft cloth which ishalf dry with clean water or neutral detergent. Don’t wet the internal components.
  1. Sewage cup
  • When dirt water cup is full, the appliance will turn off automatically and the screen will display so and voice prompt will indicateso.
  • It is recommend to clean the residuefound on inner wall of the cup by small cleaning brush tool.
  • Install the clean cup back to the appliance body tillyou hear a “click”.

  1. Intelligent dirt sensor
  • When floor is clean but the display screen shows red ring light orthe red light keep flashing, the dirt sensor may be blocked by residue.
  • Take out the sewagecup, clean the tunnel by a clean cloth or cleaning

  1. HEPA filter
  • Clean HEPA under flowingwater after each use, and make sure the HEPA dry completely before reassemble.
  1. Rolling brush
  • Pull up the left roller handle by hand and pull it outward to remove roller.
  • Remove the roller handle and use the roller cleaning brush to remove tangled hairs or debris from the brush.
  • Then rinse the roller brush with clean water.
  • Please wipe the stains on the nozzle with a wet cloth.Don’t rinse.
  • After cleaning, insert the handleless end of the roller into the corresponding drive cone, and then insert the end with the handle
  • Snap into the left slot of the rollerbrush.

 

CAUTION

  1. The product is not intended for use by persons with physical, sensory, intellectual disabilities or persons (including children) who lack experience and common senseunless supervised or instructed by others to ensure safe use.
  2. Do not touch the plug of the product with wet hands to avoid the risk of electric shock.
  3. If the adapter or plug is damaged, please stop using it. Please call for professional help.
  4. Please keep the product away from long hair, loose clothes, fingers and other foreign objects. Don’t put any part of the producttowards eyes, ears or put them into your 
  5. In case of electric leakage, motor overheat,abnormal sound, peculiar smell or weak suction, stop using immediately and call for professional maintenance.
  6. Please use our original adapter to charge. Other types of chargers may cause battery failure or extreme thermal effects.
  7. If you don't use this product for a long time, turn off the power and disconnect the plug of the charging base.
  8. After using the appliance, please clean the sewagecup in time to keep the air tunnel unblocked, so as to avoid suction compromise or motor heating that may affect the service life of the product.
  9. After using the appliance, please store it in a dry environment. Wet environment will affect the insulation and the service
  10. The appliance body and the floor brush contain electric parts, and cannot be washed with water.
  11. Please check the suction nozzle regularly. If there is any blockage, please remove it in time to avoid the decrease of suction, which will affect the performance of the appliance.
  12. Be sureto turn off before replacing the roller.