Countertop Drinking Water Filtration JSQH001 User Manual English Version

Ⅰ. Specification parameters

Ⅱ. Product diagram

Ⅲ. Operation instruction

• Procedure 1- Install the clean water/raw water switch

• When installed on the faucet with thread on the outside

1. Screw on the bubbler of the tap
2. Install clean/raw water switch gasket
3. Install the clean/raw water switch and tighten the nuts

• When installed on a threaded faucet inside

1. Screw on the tap bubbler
2. Install internal and external tooth converters
3. Install clean/raw water switch gasket
4. Install the clean/raw water switch and tighten the nuts

• When installed on a bubbler-free faucet

1. Install the universal connector onto the faucet
2. Install the clean/raw water switch and tighten the nuts
3. If the diameter of the faucet is 19-25mm, please remove the small seal on the universal joint first, and then install it according to the installation method

• Installation Step 2-- Tap installation

• Remove the random delivery faucet from the foam and check that the faucet is in good condition. Insert the end of the discharge faucet equipped with a sealing ring into the corresponding hole of the water purification port of the fuselage, and ensure that the installation is in place.

• Warm reminder

1. After the machine is installed, turn on the faucet first, turn on the clean water/raw water switch to the clean water mode, and check whether the connection part is leaking;
2. After the new machine is installed or replaced with an ultrafiltration composite filter element, open the faucet first, and turn on the clean water/raw water switch to water purification mode. After making water for 15 minutes, turn off the faucet and let it stand for at least 12 hours. Then turn on the machine and turn on the faucet. After making water for another 15 minutes, the machine can be used normally.
3. After the water purification is switched, because there is still a certain water pressure in the filter cylinder, the water purification mouth will still run for a few seconds. This phenomenon is not a machine fault, it can be used normally.

• The use of the "clean water/raw water switch" is as follows:

1. Raw water mode: Turn the switch handle to the vertical down position, open the faucet, and the water is raw water.
2. Water purification mode: Screw the switch handle to the horizontal position, open the faucet, water is clean
   

Ⅳ. Cleaning and maintenance

• The recommended replacement cycle of the filter element

1. Ultrafiltration composite filter element for 9-12 months

• Filter element replacement method:

1. Please turn off the faucet, put the machine in place, remove the top cover, use the special wrench that comes with the machine, and rotate the filter cap.
2. Take out the filter element to be replaced, load the new filter element, tighten the filter cap with a wrench, and cover the upper cover.
3. Filter element replacement note: Filter element placement direction, filter element end cover in the middle of the hole downward.

• If foreign matter is blocked on the filter screen of the clean water/raw water switch, the water volume will become smaller. Please follow the following steps to maintain it.

1. Unscrew the nut, remove the switch, and take out the gasket;
2. Unscrew the lower nut, take out the sealing ring, bubbler, and filter;
3. Clean the filter, bubbler, and lower nut;
4. Install the switch according to the splitting sequence.
   

Ⅴ. Product precautions

1. Please install it on municipal tap water, otherwise, it may affect the water quality and filter element life.
2. If not used for more than a week, when using it again, please open the water purification switch for 10 seconds to clean the water inlet.
3. The replacement cycle of the filter element varies according to the difference in water quality, water pressure, and water consumption.
4. Do not be in the "water" mode, filter more than 40° C of hot water, overheating water will lead to filter element damage!
5. Please pay attention to prevent icing inside the filter element.