Faucet Water Filter JSQH002 User Manual English Version

Ⅰ. Specification parameters

Ⅱ. Product diagram

1. Diatomite ceramic filter element   
2. Filter cartridge cover
3. Raw water/clean water outlet   
4. Water distribution switch
5. Water purifier host   
6. Teflon tape
7. Silicone gasket 
8. Adapter
9. Connect nut 
10. Adapter wrench 
11. Universal joint

 Ⅲ. Usage method

• Instructions for use:

1. This faucet water purifier can only be used to filter tap water from the municipal water supply.
2. When using the purified water, please make sure the water temperature does not exceed 38℃.
3. When using it for the first time, a small amount of filter cartridge powder may be released. Please flush with water for 60 seconds before use.
4. Before everyday use, please flush the filter cartridge with water for 10 seconds.
5. If not used for a long time, before using it again, please flush the filter cartridge with water for 60 seconds.
6. This product is only suitable for indoor use and should not be used under direct sunlight or outdoors.

• How to use:

1. After installing the water purifier, turn on the tap, and switch the water purifier's water diversion valve to the purified water position. The filtered water will flow out from the purified water outlet. Switch the water diversion valve to the original water position, and unfiltered tap water will flow out from the original water outlet.

• Usage tips:

1. Do not use water with a temperature exceeding 38℃ to flow through the water purifier as it may damage the water purifier. Do not use steel wool, abrasive cleaners or corrosive liquids (such as gasoline or acetone) to clean the water purifier. These substances may cause the product to rupture, discolor or deform.

• Warm reminder:

1. It is recommended to boil the filtered water before drinking.
2. It is recommended to replace the filter cartridge every 6 months for optimal results. Note: The actual lifespan of the filter cartridge mainly depends on the quality of the tap water and daily water consumption.

• Precautions before installation:

1. Ensure that the water tap to be installed is closed.
2. Choose the appropriate adapter according to the type of water tap.
3. The included adapter makes the water purifier suitable for almost all kitchen faucets.
4. Keep the water tap pressure between 0.1MPa~0.4MPa. If the water pressure is too low, the filtered water flow rate will be slow. If the water pressure is too high, it will affect the filtration effect.

• Installation Method of Water Tap with Threaded Outlet

1. Unscrew the fittings and filter screen on the water tap.

2. Unscrew the connection nut on the main body of the water purifier, choose an adapter that is suitable for the water tap, and match it with the corresponding silicone sealing ring.

3. Fit the connection nut onto the adapter.

4. Use the adapter wrench to screw the adapter into the water tap and tighten it.

5. Open the filter cartridge cover, remove the filter cartridge, peel off the protective film, and then put the filter cartridge back in its original position.

6. Cover the filter cartridge cover, and securely connect the water tap and water purifier with a connection nut (when installing, ensure that the silicone gasket ring inside the water purifier is tightly connected to the water tap) and tighten it to ensure there is no water leakage.

• Installation Method of Water Tap without Threaded Outlet

1. Completely fit the swivel joint on the installation position of the water tap and secure it with screws.

2. Open the filter cartridge cover, remove the filter cartridge, peel off the protective film, and then put the filter cartridge back in its original position.

3. After covering the filter cartridge cover, unscrew the connection nut on the main body of the water purifier. Choose an adapter that is suitable for the water tap, match it with the corresponding silicone sealing ring, and then screw on the connection nut.

4. Secure the water tap and water purifier with a connection nut (when installing, ensure that the silicone gasket ring inside the water purifier is tightly connected to the water tap) and tighten it to ensure there is no water leakage.

Ⅳ. Cleaning and Replacement of the Filter Cartridge

1. Ensure that the tap is turned off.
2. Unscrew the filter cartridge sleeve cover and remove the filter cartridge.

3. Use a clean cloth or soft brush to clean the surface of the filter cartridge. When cleaning, make sure to keep the outlet of the filter cartridge facing upward to prevent dirt from entering it.
4. After cleaning,  rinse the surface of the filter cartridge with clean water, and then put the filter cartridge back into the filter cartridge housing. If replacing it with a new filter cartridge, simply insert the new filter cartridge into the housing and cover the protective cover.

5. After installation, discharge water from the purifier for 60 seconds before normal use.

Ⅴ. Notes

• Note: All contents in this project are related to safety, and users must comply with them.
• These notes are only for the correct use of this product.
• The notes explain the level of danger and harm, as well as accidents that may occur.
• Prohibitions:

1. Do not use other accessories without the manufacturer's permission. If mechanical failure occurs as a result, the warranty will be terminated automatically.
2. In case of failures, immediately turn off the main water pipe switch and do not put the defective product in working order.
3. This product can only be repaired in authorized service centers. Repairing it in non-authorized service centers can cause other unsafe factors.

• Warnings:

1. Children and people without behavioral ability should use this product under the supervision of guardians.
2. In case of failures, immediately turn off the main water pipe switch and do not put the defective product in working order.
3. All pipeline construction processes should comply with national and local government regulations.

• Precautions:

1. If additional components are required to meet installation requirements, please choose high-quality products.
2. This product is suitable for the municipal tap water supply, water pressure of 0.1 MPa ~ 0.4 MPa, and water temperature of 5℃~38℃. The ambient temperature should be between 4℃ and 40℃. It is strictly forbidden to use it beyond the specified range. If the water pressure exceeds the specified range, a pressure-reducing valve should be installed. This product is only suitable for indoor installation, and a reliable floor drain should be available within 1.5 meters around the installation to avoid possible losses caused by water leakage due to blocked drainage.
3. When the product is not used for more than 3 days or left unattended, please turn off the water source to prevent water hammer impact caused by unstable water pressure, which may damage or leak the product.