FAUCET WATER FILTER JSQH006 User Manual English Version

FAUCET WATER FILTER JSQH006 User Manual

 I. Specification Parameters

II. Product Overview

① Filter Cartridge Cover

② Purified Water Outlet

③ Base Support

④ Ultrafiltration and Activated Carbon Block Composite Cartridge

⑤ Faucet Connector

⑥ Water Distribution Switch

⑦ Food-Grade PVC Tubing

⑧ Tubing Connector Nut

⑨ Shut-off Valve

A Universal Connector

B M24/M22 External Thread Connector

C M24 Internal Thread Connector

D M22/M24 Sealing Gaskets

III. Installation Methods

For your convenience, the shut-off valve, food-grade PVC tubing and faucet connector (includes one gasket) are pre-assembled.

1. Install the Faucet Connector

(1)  When installed on a faucet without a tap aerator

① Install the universal connector onto the faucet, and tighten the clamping screw to avoid water leakage. During installation, remove the sealing rubber sleeve to adjust the inner diameter of the universal connector based on the faucet's diameter;

② Connect the faucet connector to the universal connector and tighten the nuts.

Note: Screwdriver is not included in the product. Please have one ready for use prior to installation.

(2) When installed on a faucet with internal threads

① Unscrew the faucet aerators, put the corresponding sealing gasket on M22/M24 external thread connector, install the external thread connector (with the gasket) onto the faucet and tighten the nuts;

② Connect the faucet connector (ensure the included gasket is properly positioned) to the external thread connector and tighten the nuts.

(3) When installed on a faucet with external threads

① For a M22 faucet: Unscrew the faucet aerators, install the faucet connector (ensure the included gasket is properly positioned) onto the faucet and tighten the nuts.

② For a M24 faucet: Unscrew the faucet aerators, put the sealing gasket into the M24 internal thread connector and install the internal thread connector (with the gasket) onto the faucet. Connect the faucet connector (ensure the included gasket is properly positioned) to the internal thread connector and tighten the nuts.

2. Install the Shut-off Valve

Insert the shut-off valve to the base support. Rotate the valve clockwise until it is vertically upright and ensure the installation is in place. Pull the small clip on the base out and secure it into the lower part of the single valve.

3. Install Purified Water Outlet

①Insert the end of the purified water outlet equipped with a sealing ring into the corresponding hole of the base support, and ensure that the installation is in place.

②Place the water filter near the sink, ensuring that the water outlet is positioned above the sink.

4. Filter Cartridge Replacement

① Rotate the filter cartridge cover counterclockwise and remove the cover from the base support.

② Takeout the filter cartridge by pulling it out vertically.

③ Align a new filter with the filter installation port and slowly press it down until the filter is securely fixed in place. Install the cartridge cover to the base support by rotating the cover clockwise.

IV. How to Use

1. After receiving the water filter, rotate the filter cartridge cover counterclockwise to remove the cover and tear off the protective film of the filter cartridge before initial use.

2. After installation, turn on the faucet:

When the water distribution switch is positioned parallel to the countertop surface, purified water flows out from the water outlet of the water filter;

When the water distribution switch is positioned vertically to the countertop surface, unfiltered tap water flows out from the faucet.

3. During initial use, it is normal that the water filter may produce black water. This is because the filter uses activated carbon and some fine particles may be released during transportation. Flush the filter for 10 minutes before use.

4. It is recommended to flush the filter for 3-5 minutes every day before use.

V. Cleaning and Maintenance

1. Cartridge Replacement

Notes:

(1) To achieve better performance, Replace the filter cartridge regularly. You can purchase the compatible replacement filters at the Simplus store.

(2) The service life of the filter cartridge is based on average water quality standards in different regions. If the actual water quality or machine usage frequency differs significantly from the average standards, the actual service life of the filter may vary significantly and problems such as premature clogging or ineffectiveness may occur. In such case, the actual condition of the filter should be used as the basis for replacement, and you should promptly contact the local after-sales service department.

(3) The estimated service life is based on the average water usage of a typical household. The faucet water filter is intended for home use only and should not be installed in high water consumption public settings.

VI. Operating Precautions

1. Upon receiving the package, check if the product is delivered without any damages and has the required accessories enclosed.

2. Simplus Faucet Water Filter is suitable for municipal tap water, with a water pressure range of 0.1-0.4 MPa, a water temperature range of 5-38°C, and an ambient temperature range of 4-40°C. It is strictly prohibited to use it beyond these limits.

3. Simplus Faucet Water Filter is for indoor use only. Ensure that there is a reliable floor drain within a 1.5-meter radius of the filter to prevent potential water leakage and damage resulting from it.

4. Do not install Simplus Faucet Water Filter in areas exposed to direct sunlight or outdoors to avoid component aging.

5. Do not use Simplus Faucet Water Filter in high-temperature, humid, or waterlogged environments, and keep flammable or explosive materials away from the filter.

6. If additional accessories need to be purchased for installation, please select qualified products.

7. It is recommended to boil the purified water before drinking.

8. Simplus shall not be liable for any consequences resulting from any failure to comply with the above operating precautions.

9. Simplus Faucet Water Filter is compatible with most faucets; however, it cannot be installed on the faucets with the following specifications:

(1) Faucet front end to lower edge is 15mm or less

(2) Faucet front end diameter is 25mm or more

(3) Faucet front end diameter and conversion connector don't match

(4) Faucet front end abnormality

(5) Faucet front end with aspersed type shower head

(6) Equipped with sensor faucets.

10. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

11. Children should be supervised not to play with the appliance.