SG/MY-PET CARE VACUUM CLEANER CWHL001 USER MANUAL

SPECIFICATIONS

ILLUSTRATION

1. Carrying handle
2. Release button lid
3. Air inlet
4. Flexible hose
5. Power cable connection
6. Air outlet
7. Accessory holder
8. Release button of dust container
9. Top hose connection
10. Dust container
11. Cyclone cone
12. Lid

1. Cyclone cone
2. Rotary switch
3. Flexible hose
4. Base
5. Dust container

1. Off
2. Low suction power
3. High suction power
4. Heating to switch on

Accessories

1. Electric clipper
2. Round brush
3. Massage brush
4. De-matting brush
5. 2-in-1 combination nozzle for vacuuming and drying
6. 2x accessory brackets

OPERATION

• Removing and attaching the dust container

1. Before removing/attaching the dust container,turn the rotary switch to the Off" position.
2. Press both locks on the dust container's release buttonsat the same time to release the dust container [1].
3. Remove the dust container by lifting it upwards [2].
4. Then place the dust container back on the baseuntil it audibly clicks into place. When inserting, make sure that the suction inlet and the upper hose connection are on top of each other.

• Removing and replacing the lid

1. Before removing/replacing the dustcontainer, tum the rotary switch to the “Off" position.
2. Press both locks on the lid release buttonsat the same time to release the dust container [1]
3. Remove the lid by lifting it upwards [2]
4. Then place the dust container back on thebase until it audibly clicks into place.

• Attaching and removing the hose

1. The device can be used forvacuuming and drying.
2. To do this, place the hose on thecorresponding connection on the 
3. Make sure that the hose audiblyclicks into the corresponding 
4. To remove the hose, press therelease button on the hose and pull it off the device.

①Air inlet for suction

②Air outlet for drying

③Hose connection

• Operating the accessories

The accessories can be attached to the flexible hose as required. Make sure that the corresponding accessories audibly click into place for safe handling. The accessories can be removed from the hose end again by holding down the release button at the end of the hose.

1. Electric shearing machine

The electric shearing machine requires a 5V 1A charger to charge. The charging status is displayed as follows:

• The green light flashes while charging.
• The green light is on when the battery is fully charged.
• There is no indicator when the device is turned on.

①Shaving head

②Locking button

③Release button

④USB charging socket

⑤2 comb attachments

2. Attaching the shearing machine to the vacuum cleaner

• Place the clipper attachment onto the hose (Fig. 1) and attach the clipper with the top (shaving head) to the upper end of the handle as shown in the illustration (Fig. 1).

①lower hose connection

②Apply with some pressure

①Press

②Insert the clipper into the designated place at the top of the handle

③Fastening device for the clipper

• Press the handle of the clipper into the locking buckle until it audibly clicks into place.
• Assembly complete.You can now start shearing.

①Press

②Locking buckle

3. Attaching and removing the shearing machine

①Pull

②Press down button

③Pull out

④Press the release button

A notice:

• The electric shearing machine requires a 5V 1A charger. The charging status is displayed as follows:
• The green light flashes while charging.
• The green light stays on when the battery is fully charged.
• There is no indicator when the device is turned on.

4. Using the different brush attachments

（1）Round brush

①Brush release button

②Press

③attaching the round brush to the hose: apply with some pressure

④&⑤ Removing the round brush from the hose: ④press the release button&⑤pull out

（2）2-in-1 combination nozzle for vacuuming and drying

Depending on your needs, this brush can be used to dry or vacuum the fur or the surrounding area.

1. Attaching the combi brush to the hose: ① apply with some pressure
2. Removing the combi brush from the hose: ② press the release button ③ pull out

（3）Massage brush

If you want to remove the hair from the massage brush, you can press the massage cushion release button to remove the massage cushion.

①massage seat release button

②Massage base

③Press

1. Attaching the massage brush to the hose: ① apply with some pressure
2. Removing the massage brush from the hose: ② press the release button ③ pull out

（4）De-matting brush

While combing, keep the button on the base plate pressed.

①Press

②Button on the base plate

1. Attaching the de-matting brush to the hose: ① apply with some pressure
2. Removing the de-matting brush from the hose: ②press the release button ③pull out

CLEANING AND MAINTAINCE

1. Use neutral detergent or water to wipe the machine. Wring out the cleaning cloth before wiping to avoid water entering the inside of the machine. It is recommended to place the machine upright after cleaning and avoid indirect sunlight and humid places.
2. Before cleaning, unplug the power supply and turn off the machine.
3. The attachments can be stored on the device to save space using the two accessory holders. To do this, snap the accessory holders into the notches provided.
4. Store the device in a dry place. Storing it in a humid environment may affect the insulationand shorten its lifespan.

CAUTION

1. Keep away from water. Do not use this device near bathtubs, showers,wash basins or other containers containing water.
2. Never pick up an electrical device if it has fallen into water. Unplug it immediately.
3. Do not immerse the device itself or the power cord or plug in water.
4. Do not use the device with extension cords or timers.
5. Always check the device for damage before using it. If the device shows visible damage, do not use it.
6. Do not use the device if it has malfunctioned or fallen into water.
7. Never touch the device, power cord or plug with wet hands.
8. Do not insert metal objects into the device to avoid electric shock.
9. Always place the device on a level surface and avoid heavy falls or impacts.
10. Keep the ventilation and the moving parts of the device away from long hair, loose clothing and body parts. Do not point the hose and accessory brush head at your eyes or ears and do not put it/them in your mouth.
11. Keep a sufficient distance from heat sources such as fireplaces or heaters.
12. Do not vacuum up materials:

- that have a high temperature, e.g. cigarette butts, ash, matches, etc.

- Fine materials such as plaster powder, ash, wood chips, etc.

- Dangerous materials such as solvents, limescale cleaners, etc.

- or other materials with unknown physical properties

13. Do not use the device to vacuum up liquid substances to avoid a short circuit in the device.
14. Do not use the device to vacuum up sharp or pointed objects to avoid damaging the device. e.g. pins, broken glass, stones.
15. Always switch the device off before unplugging the power cord.
16. Do not pull the power cord to unplug the power cord from the socket.
17. The device must not be used outdoors.
18. Before transporting the device, check that the plug is removed from the housing and that the power cable is properly stowed.
19. Store connected hoses properly before transporting.
20. Do not use the hose to vacuum up a large amount of densely packed hair.
21. The device could become clogged.
22. Only use the device with the correct mains voltage as indicated on the rating plate. Using a voltage that does not match the specifications of this device can cause motor damage.
23. ! Do not use the device near flammable materials, as there is a risk of fire and explosion!

TROUBLESHOOTING

If the device is not working properly, check whether you can solve the problem yourself. If the steps above do not solve the problem, please contact customer service.

Do not attempt to repair an electrical device yourself!