Ⅰ. Specification parameters
Product name |
Model No. |
Rated voltage |
Rated Frequency |
Consumption Power |
Appliance Classes |
Stand Fan |
RSK-2 |
220-240V |
50Hz |
45W |
ClassII |
Ⅱ. Product diagram and installation steps
- Assembly instructions:
- Insert the A tube into the circular hole in the middle of the base, and secure it with an L-shaped screw from underneath (see Figure C).
- Install the B tube and fasten it with the fixing screw. Note: if used as a table fan, the B tube is not needed.
- Install the motor head and fasten it with the fixing screw, then follow the installation steps for the motor head.
- Motorhead installation steps:
- Turn the blade clockwise to remove the blade set, and counterclockwise to remove the net set.
- Install the back net on the motor shaft in the direction shown in Figure D, and secure it with the net set.
- Align the groove on the back of the fan blade with the shaft connector on the motor shaft, then install it on the motor shaft and secure the blade set counterclockwise on the motor shaft.
- Place the front net on top of the back net, align it with the fixing screw hole, and secure it tightly.
- Tighten the back net screws.
Ⅲ. Operation instructions
- Place the fan on a dry and flat surface.
- Insert the plug into a 110V AC power outlet.
- Use the speed adjustment knob on the motor head to select the desired speed (3-high speed, 2-medium speed, 1-low speed, 0-off).
- Oscillation function: the oscillation lever is located above the motor housing. Push the lever down to start oscillation and pull it up to stop.
Ⅳ. Product cleaning:
- Turn off the fan and unplug it before disassembling or cleaning.
- Use a soft cloth dampened with warm soapy water to clean the outer casing, and then dry with a soft cloth. Do not use any organic solvents or chemical cleaners on the fan.
- Do not directly spray water onto the fan when cleaning. Do not let water enter the motor.
Ⅴ. Important safety instructions:
- Please read and save these instructions to reduce the risk of fire, electric shock, or injury during use.
- Follow the instructions in this manual to use the fan. Do not use any operations that may cause fire, electric shock, or injury.
- The fan is suitable for household use only and is not intended for commercial or industrial use.
- Avoid direct sunlight on the fan.
- Do not immerse the fan plug or power cord in water or any other liquid, and do not spray water or other liquids on the fan.
- Use the fan on a dry and flat surface.
- A loose connection between the plug and outlet may cause high temperatures and plug deformation.
- Turn off and unplug the fan before moving or cleaning it. Grasp the plug firmly and pull it out of the outlet. Do not pull the cord to unplug it.
- Do not use the fan if the power cord, plug, or body is damaged or falls.
- Do not use the fan in the presence of flammable or explosive materials.
- Do not place the fan or any parts near a heat source, kitchen appliances, or heaters.
- Do not use the fan if the outer casing is detached or damaged.
- Do not touch the rotating parts of the fan.
- Keep the fan away from children and supervise children when using the fan.
- Do not hang the fan on walls or ceilings.
- Do not use any accessories or speed controllers not recommended for use with this fan.
- Children should be supervised to ensure they do not play with the electrical appliance.
- This electrical appliance is not suitable for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
- If the power cord is damaged, it must be replaced by the manufacturer or authorized service representative to avoid danger.
- Warnings and precautions:
- If abnormal behavior is observed, immediately unplug the fan and notify the service provider. Do not attempt to disassemble the fan on your own to avoid danger.
- Do not use any solid accelerator devices to avoid fire or electric shock hazards.
- Make sure the power outlet is 110V before use.
- Do not tilt the fan to avoid damage or tipping.
- Do not use the fan in high-temperature or damp environments.
- Turn off the fan and unplug it before removing the front or rear guard.
- If any abnormalities are observed, immediately turn off and unplug the fan and take it to a dealer for repair.