Ⅰ. Specification
|
Name |
Garment steam iron |
|
Wattage |
2000W |
|
Voltage |
220-240V~ |
|
Rated frequency |
50Hz |
Ⅱ. Components and Installation Drawing
- Spray Head
- Holding Hanger
- Holding Nips
- Steam Hose
- Telescopic Rod
- Water tank
- Steam Pipe connector
- Mode Switch
- Indicator Light
- Base
Ⅲ. Use Method
- Insert the telescopic aluminum rod into the telescopic aluminum rod holder.
- Push the button to stretch the telescopic aluminum rod upward or adjust it to the proper position, and press the button.
- Insert the hook and telescopic aluminum rod together.
- Insert the steam hose into the steam outlet, and switch clockwise to lock.
- Counterclockwise to unscrew the water tank, fill cold water in the water tank, and clockwise to lock back.
- When setup the water tank on the appliance, the garment steam iron indicator will light up.
- Run 35 seconds, garment steam iron is ready to use.
Ⅳ. Introduction to Cleaning and Maintenance
- Cleaning and storage
- Be sure to unplug the power cable before cleaning and maintenance.
- Do not wash the device with water directly; wipe it with a soft cloth with a little neutral detergent, and do not use solvents such as gasoline.
- After cleaning and maintenance, it is necessary to wait until it is fully dry before using or storing it.
- If it is not used for a long time, please clean the product, wait for it to dry, retract the adjustable tube, remove the pipe, remove the hanger, put it back in the original packaging box, and store it in a cool and dry place.
- Cleaning methods of dirt and sediment
- Mix50% vinegar and 50% water , about 900ml.
- Pour the mixture into the devicet from the pipe connection.
- Let the mixture fill half of the water tank.
- Wait40 mins.
- Open the drain valve at the bottom of the equipment to drain the mixture.
- Remarks : Change the mixture into clean water and repeat the operation several times according to the above steps to achieve the cleaning effect.
Ⅴ. Attention
- Please use the correct power supply voltage and frequency：220-50 Hz, do not share the same power supply with other high-power electrical appliances.
- It can't be placed in water or liquid.
- Do not add hot water to the water tank, which will cause deformation of the water tank.
- Pay attention to the safety of the plug, socket, and power supply. Do not drag or pull the plug.
- If the power cable is damaged, please return it to the factory for repair or replacement.
- It is forbidden to start the power supply before adding water.
- This product is only for indoor use.
- The product can only use a socket with a grounding wire.
- Do not use the product on the table or chair, only use it when the product is on the ground
- Always check the power cable and pipe for damage.
- Before use, be careful that hot water will be ejected from the hole
- Don't touch the hot position and hot brush head, and pour the residual water carefully to avoid scalding.
- Don't pull out the pipe during use.
- Please don't leave while the product is powered on.
- During the use of the product, don't let the power cable contact with the pipe and high-temperature steam
- Don't let the plug contacts the heating position. After use, let the device cool down and then pour the water. If it is not used for a long time, please remove the water and pull out the plug.
- Please return to the factory for repair when the parts are damaged. Incorrect repair will cause damage, fire, and electric shock.
- Let the device cool naturally after use.
- When don't use it, please pull out the power plug.
- This product is not recommended to be used by people (including children) who are physically unsound, feel or mentally handicapped, or lack relevant experience, and only, unless the person responsible for their safety supervises and instructs them to use this product.
- Children should be taken care of to ensure that they do not play with the product.
Ⅵ. FAQ
- Q1: How to hang the iron board on the steamer?
- A1: Under the back of the iron board, there are two clips that can be clipped on the telescopic rod. When you do the flat iron, You can locate the bayonet of the back of the iron board to the top of the telescopic rod.
- Q2: What's the difference between 002, 009 and 012 types? Which one should I order?
- A2: Dear if you want bigger steam, you can choose the 002 type, which is with 10 holes to release steam. Besides, it comes with 10 modes for different fabric types. If you prefer the better material and easiness to use, you can choose 009, which only comes with one button to control on or off. Furthermore, it's with the best material among these three types. If you want a high watt one and cheaper one, you can choose the 012 type.
- Q3: Why will it leak water from the steamer head?
- A3: It's normal that a little water is left on the clothes because the steam will gather together when the steamer head contacting the clothes. Please lift the steamer head higher than 1.3m when you use it.
- Q4: How to add water into the water tank?
- A4: There is a water tank valve under the water tank, and you can screw it off to add water in. And then screw the valve back to the water tank and put it back on the machine.