Ⅰ. Product parameters
Item No: |
GTJH002 |
Steam temperature |
98°C |
Power Supply |
220-240V 50-60Hz |
Mist output |
30g/min |
Power |
1800W |
Water tank capacity |
1.6L |
Ⅱ. Drawing
- Telescopic rod fixing sleeve
- Tracheal fixation sleeve
- Knob switch
- Indicator light
- Base
- Bottom drain valve
- Water tank
- Water tank handle
- Expansion rod
- Expansion clip
- Hanger
- Spray head
Ⅲ. Operation Instructions
- Please check before use
- Check whether the steam pipe and water inlet are blocked. If there is any blockage, please remove the blockage. If the power cable is damaged, please do not dismantle the machine without authorization. Please return it to our company for repair or find a professional to repair and replace it.
- Usage method
- Screw the pipe to the steam port of the device and tighten it directly
- Insert the adjustable tube into the device hole, directly press it to the end, or it will shake unsteadily
- Open the snap and lengthen the tube, there are three sections of the tube.
- Vertical ironing
- Fix the ironing board on the adjustable tube and press it down slowly from the top of the adjustable tube
- Install the hanger rod on the hanger
- Put the top of the adjustable tube at the bottom of the hanger
- Please place the steam nozzle on the hanger, and the garment steamer installation is completed
- Flat ironing
- Insert the ironing board bracket into the ironing board, please insert it tightly
- The bracket hole of the ironing board is directly inserted into the top of the adjustable tube
- Method of adding water
- Turn on the water tank knob and fill the tank with water. After filling with water, tighten the water tank knob, then put the water tank into the device.
- Safety protection device:
- Power indicator display. Rotary switch, freely adjustable
- Thermostat. Control the heater to work between the limited temperature, effectively preventing the danger caused by too high temperature.
- Thermal fuse. When the heating temperature rises too high, the thermal fuse will fuse, which can automatically protect and prevent danger.
Ⅳ. Introduction to cleaning and maintenance Cleaning and storage
- Be sure to unplug the power cable before cleaning and maintenance
- Do not wash the device with water directly; wipe it with a soft cloth with a little neutral detergent, and do not use solvents such as gasoline
- After cleaning and maintenance, it is necessary to wait until it is fully dry before using or storing it
- If it is not used for a long time, please clean the product, wait for it to dry, retract the adjustable tube, remove the pipe, remove the hanger, put it back in the original packaging box, and store it in a cool and dry place
- Cleaning methods of dirt and sediment
- Mix 50% vinegar and 50% water, about 900ml
- Pour the mixture into the device from the pipe connection
- Let the mixture fill half of the water tank
- Wait 40 mins
- Open the drain valve at the bottom of the equipment to drain the mixture
- Remarks: Change the mixture into clean water and repeat the operation several times according to the above steps to achieve the cleaning effect.
Ⅴ. Attention
- Please use the correct power supply voltage and frequency:220-50 Hz, do not share the same power supply with other high-power electrical appliances.
- lt can't be placed in water, Liquid.
- Do not add hot water to the water tank, which will cause deformation of the water tank.
- Pay attention to the safety of the plug, socket, and power supply. Do not drag or pull the plug
- If the power cable is damaged, please return it to the factory for repair or replacement
- It is forbidden to start the power supply before adding water
- This product is only for indoor use
- The product can only use a socket with a grounding wire.
- Do not use the product on the table or chair, only use it when the product is on the ground
- Always check the power cable and pipe for damage ll. Before use, be careful that hot water will be ejected from the hole
- Don't touch the hot position and hot brush head, and pour the residual water carefully to avoid scalding.
- Don't pull out the pipe during use.
- Please don't leave while the product is powered on
- During the use of the product, don't let the power cable contact with the pipe and high-temperature steam
- Don't let the plug contacts the heating position. After use, let the device cool down and then pour the water. If it is not used for a long time, please remove the water and pull out the plug.
- Please return to the factory for repair when the parts are damaged. Incorrect repair will cause damage, fire, and electric shock.
- Let the device cool naturally after use. When the heating temperature rises too high, the thermal fuse will fuse, which can automatically protect and prevent danger.
- When don't use it, please pull out the power plug
- This product is not recommended to be used by people (including children) who are physically unsound, feel or mentally handicapped, or lack relevant experience, and only, unless the person responsible for their safety supervises and instructs them to use this product.
- Children should be taken care of to ensure that they do not play with the product.
- Do not immerse the product in water or rinse with water.
- Be careful of the hot steam, which may cause burns.
- It is forbidden to plug the plug with wet hands to avoid electric shock or fire, this product is correct.
- It is strictly forbidden to disassemble the machine without authorization.
- In case of failure, please return it to the sales shop.