Multifunctional hanging ironing machine
Instruction manual
Please refer to the actual products
Dear use in order to make you use this products correctly, Please read this manual carefully before use
Product features
Brief introduction:
This product is a high-grade ironing appliance, which is suitable for household use. It's an ideal ironing appliance for cleaning and ironing fabrics. Beautiful design makes the product more elegant. The product is suitable for ironing and disinfecting clothes, curtains and carpets of different materials. It's easy to use, convenient to operate and saves energy and time.
Please check before use
Check whether the steam pipe and water inlet are blocked. If there is any blockage, please remove the blockage. If the power cable is damaged, please do not dismantle the machine without authorization. Please return it to our company for repair or find a professional to repair and replace it.
Safety protection device:
- Power indicator display Rotary switch, freely adjustable Z.thermostat
Control the heater to work between the limited temperature, effectively preventing the danger caused by too high temperature.
3.Thermal fuse
When the heating temperature rises too high, the thermal fuse will fuse, which can automatically protect and prevent danger.
Warranty:
l.lf the power cable, plug and air duct are damaged, they must be repaired and replaced by our company in order to avoid danger.
- When using the product, Please pay more attention to prevent the danger caused by steam splashing.
- When adding water and cleaning, the power cord should be pulled out
Attention
l.Please use the correct power supply voltage and frequency :220-50 Hz, do not share the same power supply with other high-power electrical appliances. Brief introduction: 2.lt can't be placed in water, Liquid.3.Do not add hot water into the water tank, which will cause deformation of the water tank.
4.Pay attention to the safety of plug, socket and power supply. Do not drag or pull the plug
5.lf the power cable is damaged, please return to the factory for repair or replacement Catalog
6.It is forbidden to start the power supply before adding water
- This product is only for indoor use
- The product can only use socket with grounding wire Please check before use:
- Do not use the product on the table or chair, only use it when the product is on the ground
- Always check the power cable and pipe for damage ll. Before use, be careful that hot water will be ejected from the hole
12.Don't touch the hot position and hot brush head, and pour the residual water carefully to avoid scalding. 13.Don't pull out the pipe during use.
- Please don't leave while the product is powered on
- During use the product, don't let the power cable contact with the pipe and high temperature steam
- Don't let the plug contact with the heating position. After use, let the device cool down and then pour the water. If it is not used for a long time, please remove the water and pull out the plug.
- Please return to the factory for repair when the parts are damaged. Incorrect repair will cause damage, fire and electric shock.
- Let the device cool naturally after use. When the heating temperature rises too high, the thermal fuse will fuse, which can automatically protect and prevent danger.
- When don't use, please pull out the power plug
- This product is not recommended to be used by people (including children) who are physically unsound, feel or mentally handicapped or lack relevant experience and only, unless the person responsible for their safety supervises and instructs them to use this product.
- ChiLdren should be taken care of to ensure that they do not play with the product
Safety warning
Do not immerse the product in water or rinse with water. Be careful of the hot steam, which may cause burns.lt s forbidden to plug the plug with wet hands to avoid electric shock or fire, this products correctly. It is strictly forbidden to disassemble the machine without authorization. In case of failure, please return it to the sales shop
Usage method
- Screw the pipe to the steam port of the device and tighten it directly
- Insert the adjustable tube into the device hole, directly press it to the end, or it will shake unsteadily
- Open the snap and lengthen the tube,there are three sections of the tube.
l.Vertical ironing
Fix the ironing board on the adjustable tube and press it down slowly from the top of the adjustable tube
Install the hanger rod on the hanger
Put the top of the adjustable tube at the bottom of the hanger
Please place the steam nozzle on the hanger, and the garment steamer installation is completed
2.Flat ironing
Insert the ironing board bracket into the ironing board ,please insert it tightly
The bracket hole of ironing board is directly inserted into the top of adjustable tube
3.Method of adding water
Turn on the water tank knob and fill the tank with water. After filling with water, tighten the water tank knob, then put the water tank into the device.
Faults and problems
|
Phenomenon |
Reason |
Solutions |
1 |
Don't work |
power didn't connect |
Check the power cable and socket |
didn't turn on the device |
Turn on the device |
||
fuse is bumtout |
Ask a professional to repair it |
||
indicator light is off |
|||
power plug is loose |
|||
2 |
Have noise or little steam in the pipe |
The brush head is too low |
Raise the pipe and brush head |
3 |
Brush head water leakage |
Brush head break |
Replace the brush head |
Horizontal operation |
Vertical up and down operation |
||
4 |
Water leakage at pipe connection |
Seal ring aging |
Replace the seal ring |
Loose connection |
Tighten again |
||
5 |
Water leakage at water tank |
Water tank break |
Replace the water tank |
6 |
Little steam output |
The voltage is too low |
Turn off the high-power electrical appliances and use them after the voltage is stable |
The pipe is blocked |
Clean the pipe |
||
7 |
Water tank deformation |
Add superheated boiling water |
Replace the water tank |
Added chemical reagent |
|||
8 |
No steam but the indicator light is on |
thermostat damaged |
Ask a professional to repair it |
Components damaged |
|||
9 |
No steam output |
Steam condensation in the pipe |
Raise brush head Let the condensate flow back to the thermostat |
Product parameters
Item No: |
ZD-758 |
Steam temperature |
98°C |
Power Supply |
220-240V 50-60Hz |
Mist output |
35g/min |
Power |
1800W |
Water tank capacity |
1.8L |
Introduction to cleaning and maintenance Cleaning and storage
- Be sure to unplug the power cable before cleaning and maintenance
- Do not wash the device with water directly; wipe it with a soft cloth with a little neutral detergent, and do not use solvents such as gasoline
- After cleaning and maintenance, it is necessary to wait until it is fully dry before using or storing it
4.lf it is not used for a long time, please clean the product, wait for it to dry, retract the adjustable tube, remove the pipe, remove the hanger, put it back in the original packaging box, and store it in a cool and dry place
Cleaning methods of dirt and sediment
- Mix 50% vinegar and 50% water, about 900ml
- Pour the mixture into the device from the pipe connection
- Let the mixture fill half of the water tank
- Wait 40 mins
5.Open the drain valve at the bottom of the equipment to drain the mixture
Remarks:Change the mixture into clean water and repeat the operation several times according to the above steps to achieve the cleaning effect
Environment protection
This product is designed and manufactured with high quality materials and original parts, which can be recycled and reused. Please dispose according to Local laws and regulations. Do not treat waste products as general household waste. Proper disposal of waste products will help to avoid negative impact on environment and human health